Menu
Your Cart

2 Channel 5V Relay Board Module

Description

This is a 2 Channel isolated 5V 10A relay module Optocoupler for Arduino PIC ARM. It can be used to control various appliances and other types of equipment with a large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). 

Pin Configuration: 

  • GND – Connect 0V to this pin.
  • IN1 – Controls relay 1, active Low Relay will turn on when this input goes below about 2.0V
  • IN2 – Controls relay 2, active Low Relay will turn on when this input goes below about 2.0V
  • VCC – Connect 5V to this pin. Is used to power the optocouplers
About high level and low level-triggered mode:
  1. High-level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way;
  2. Low-level trigger refers to the signal voltage between the input terminal and Earth OV trigger, can be understood as the signal input terminal and the GND negative electrode short circuit triggered away 1-channel relay module connection. CityTechBD

Jumper Instruction = The relay can be turned on when we connect 5v to one end and the other to -5v / Gnd, while talking about the jumper, if we short the VCC and the middle pin, then our relay will act as high level-triggered relay means that when we will apply + 5V input on its input pin it will be turned on and when the jumper will be set to “middle and GND”, it will act as a low-level triggered relay, It means that relay will be triggered when we implement the 5V / GND on its input pin.

Features :

  1. 2 LEDs to indicate when relays are ON.
  2. Works with logic level signals from 3.3V or 5V devices
  3. Opto isolation circuitry
  4. Module with diode current protection, short response time
  5. Around the board with 4 mounting holes, hole diameter 3. 1 mm, easy installation and fixing
General Specification
Relay TypeLow Level Trigger
Logic Input (V)3.3 ~ 5
Trigger Voltage (VDC)5
Switching Voltage (VAC)250@10A
Switching Voltage (VDC)30@10A
Length (mm)50.6
Width (mm)39
Height (mm)19.5
Weight (gm)28
Shipment Weight0.03 kg
Shipment Dimensions6 × 5 × 3 cm

Package Includes :

1 x 2 Channel 5V Relay Board Module

Review

Write a review

Note: HTML is not translated!
Bad Good
Tags: 2 Channel 5V Relay Board Module Price in bd , 2 Channel 5V Relay Board Module Price in Bangladesh , 2 channel 5v relay board module , 2 channel 5v relay module , 12v 2 channel relay module , 4 channel 5v relay module , 12v 8 channel relay module , 5v one channel relay module , elegoo 8 channel dc 5v relay module , arduino 8 relay module wiring , 5v relay with esp32 , arduino 12v relay module , 1 channel 5v relay module , 5v single channel relay module , 2 channel relay module arduino , raspberry pi 8 relay module , arduino 8 relay module , 1 channel relay module arduino , 2 channel relay module circuit diagram , 4 channel relay module circuit diagram , 5v 1 channel relay module , 8 channel 5v relay module , 5v 8 channel relay module board , 5v relay board module , 5v 8 channel relay module board , how to make a 5v relay module , 5v relay module circuit diagram , 5v relay module arduino , arduino 12v relay module , arduino uno relay module , 5v relay with esp32 , 5v single channel relay module , arduino 8 relay module wiring , elegoo 8 channel dc 5v relay module , 5v/7-28v esp8266 wifi 8 channel relay module esp-12f development board , 5v relay module , how to use relay module with arduino , how to connect 12v relay module to arduino , how to connect relay module to arduino , connecting a relay module to a microcontroller , 5v one channel relay module , 8 channel relay with esp8266 , how to wire 5v relay , arduino 8 relay module , how to use 8 channel relay board , 12v 8 channel relay module , jd vcc in relay module , sainsmart 8 relay module , 5v relay with 3.3v , 5 volt relay module , 5v relay connection with arduino , 4 channel 5v relay module